{"id":1426,"date":"2012-08-13T09:11:46","date_gmt":"2012-08-13T13:11:46","guid":{"rendered":"https:\/\/techfragments.com\/?p=1426"},"modified":"2022-12-01T09:26:33","modified_gmt":"2022-12-01T14:26:33","slug":"graphene-internal-photoemission-spectroscopy","status":"publish","type":"post","link":"https:\/\/techfragments.com\/graphene-internal-photoemission-spectroscopy\/","title":{"rendered":"Characterization of Graphene Using Internal Photoemission Spectroscopy"},"content":{"rendered":"

Graphene, the new material in the world of future electronics manufacturing, has high carrier mobility and low noise. That is why graphene<\/a>\u00a0is seen as a promising candidate to eventually replace silicon in integrated circuits.<\/p>\n

One task crucial to the successful engineering and manufacturing of next-generation devices using new materials is developing ways to completely characterize them. Researchers at The National Institute of Standards and Technology\u2019s Physical Measurement Laboratory<\/a> have gotten one step closer to this goal with the determination of graphene\u2019s work function and the band alignment of a graphene-insulator-semiconductor structure by using the combined optical techniques of internal photoemission (IPE) and spectroscopic ellipsometry (SE).<\/p>\n

Internal Photoemission and Spectroscopic Ellipsometry<\/h2>\n

IPE and SE have been around for a long time, but it is only recently that scientists have started combining the two techniques for use in characterization of integrated circuit devices. Internal photoemission is used to gauge the energy of electrons emitted from materials in order to determine binding energies. Basically, a light is shone onto a sample and a photocurrent created by the ejected electrons is measured.<\/p>\n

In spectroscopic ellipsometry, broadband light sources are shone upon a material, and optical properties are ascertained from the reflectivity. Both techniques are truly crafts. Only a skilled specialist can perform the measurements accurately.<\/p>\n

\u201cWe are the only group in the U.S. who use the techniques full time,\u201d<\/p><\/blockquote>\n

says Nhan Nguyen, of the PML\u2019s Semiconductor and Dimensional Metrology Division. Nguyen brings a wealth of experience to the state-of-the-art facilities at NIST.<\/p>\n

\u201cNhan is one of, arguably, two photoemission specialists worldwide that have a tremendous depth and experience in that measurement technique. As far as ellipsometry, there are relatively few ellipsometric specialists that have the spectral range that he can cover with the measurement apparatuses that he has available to him at NIST,\u201d<\/p><\/blockquote>\n

explains David Gundlach, Nguyen\u2019s Project Leader.<\/p>\n

Energy Barrier Heights and Band Structure<\/h2>\n
\"A

A graphene-insulator-semiconductor sample under electrical test. Credit: NIST<\/p><\/div>\n

Nguyen initially used the combined measurement techniques to successfully establish the energy barrier heights and band structure of metal-oxide-semiconductor (MOS) devices. Building on that study, he anticipated that he could characterize a graphene-insulator-semiconductor (GIS) device in a similarly non-destructive manner.<\/p>\n

Current methods for characterizing such a device employ destructive techniques for cross-sectioning and analyzing. These methods not only destroy the device, but also potentially compromise the very electronic properties that are being measured.<\/p>\n

Band alignment is essential in GIS devices since the correct band offsets are required to prevent undesirable leakage currents in device applications. If the layers are not lined up in a specific way, the device will behave differently than anticipated, perhaps even failing entirely.<\/p>\n

This information is critical for the successful engineering and reproducible manufacturability and reliability of such devices. Nevertheless, until now, no detailed study on the band alignment of these devices had been reported.<\/p>\n

Graphene Film<\/h2>\n

Nguyen and his team investigated a structure that consisted of a graphene film grown by chemical vapor deposition (CVD), a degenerately doped p-type silicon substrate, and a 10 nm thick thermal SiO2 layer. The graphene film, a continuous one-atom layer, had the necessary properties (i.e., extremely thin, robust, continuous, and semi-transparent) to enable excellent optical transmission allowing electrical measurements well beneath the surface.<\/p>\n

Using a combination of IPE (setup included a 150 W broadband Xenon light source and a quarter-meter Czerny Turner monochromator to tune the incident light with photon energy) and SE, Nguyen was able to view the whole picture of the structure\u2019s band alignment. IPE revealed the offset between bands and how they aligned with respect to each other, but only on one side of the device.<\/p>\n

Spectroscopic ellipsometry measurements allowed the calculation of the band gaps, which led to the determination of the entire band structure.<\/p>\n

\u201cIn devices,\u201d Nguyen explains, \u201cwe want band offsets large enough so that you don\u2019t have noise or leakage. If they are too close, the electrons can jump across. With IPE, you can really look deeper below the surface of the material without changing the properties of the interface.\u201d<\/p><\/blockquote>\n

Nguyen was also able to determine the work function of the graphene layer, which can vary greatly depending on what the layer is placed upon and other environmental factors. Future studies will focus on the possibility of reproducibly controlling the energy properties of the graphene layer based on the needs of the end device.<\/p>\n

The potential impact of this completed study and published results on the development of future devices is substantial. Instead of developing a device and destructively measuring what was built afterwards to determine its electrical properties, devices can be engineered with known electrical behavior from the start.<\/p>\n

\u201cNhan\u2019s technique is extremely valuable in advancing future electronics in the fronts of semiconductor electronics, advanced manufacturing, and nanomanufacturing,\u201d<\/p><\/blockquote>\n

Gundlach concludes.<\/p>\n

Future Studies<\/h2>\n

Over and above studying the manipulation of energy levels in a graphene layer, future studies will utilize graphene\u2019s unique properties to study other materials. Since graphene can be applied in a very thin and continuous layer, it allows for much better optical transmission than the semi-transparent metals previously used.<\/p>\n

Nguyen intends to stack the graphene layer onto other layers with unknown properties, using the graphene as a key to understanding the unknown layers beneath.<\/p>\n

\u201cThis has given us access to measurements that were previously unavailable,\u201d<\/p><\/blockquote>\n

Nguyen states. This is critical as the industry moves beyond CMOS technology. New semiconductor materials used in more complicated device structures and architectures need to be characterized. Nguyen and colleagues have confirmed a non-destructive way to do it.<\/p>\n

Reference: R. Yan, Q., et al., Determination of Graphene Work Function and Graphene-Insulator-Semiconductor Band Alignment by Internal Photoemission Spectroscopy<\/a>\u00a0Applied Physics Letters, 101, 022105 (2012)<\/p>\n","protected":false},"excerpt":{"rendered":"

Graphene, the new material in the world of future electronics manufacturing, has high carrier mobility and low noise. That is why graphene\u00a0is seen as a promising candidate to eventually replace silicon in integrated circuits. One task crucial to the successful engineering and manufacturing of next-generation devices using new materials is developing ways to completely characterize…<\/p>\n","protected":false},"author":2,"featured_media":1429,"comment_status":"closed","ping_status":"closed","sticky":false,"template":"","format":"standard","meta":{"footnotes":""},"categories":[73],"tags":[12],"_links":{"self":[{"href":"https:\/\/techfragments.com\/wp-json\/wp\/v2\/posts\/1426"}],"collection":[{"href":"https:\/\/techfragments.com\/wp-json\/wp\/v2\/posts"}],"about":[{"href":"https:\/\/techfragments.com\/wp-json\/wp\/v2\/types\/post"}],"author":[{"embeddable":true,"href":"https:\/\/techfragments.com\/wp-json\/wp\/v2\/users\/2"}],"replies":[{"embeddable":true,"href":"https:\/\/techfragments.com\/wp-json\/wp\/v2\/comments?post=1426"}],"version-history":[{"count":3,"href":"https:\/\/techfragments.com\/wp-json\/wp\/v2\/posts\/1426\/revisions"}],"predecessor-version":[{"id":1432,"href":"https:\/\/techfragments.com\/wp-json\/wp\/v2\/posts\/1426\/revisions\/1432"}],"wp:featuredmedia":[{"embeddable":true,"href":"https:\/\/techfragments.com\/wp-json\/wp\/v2\/media\/1429"}],"wp:attachment":[{"href":"https:\/\/techfragments.com\/wp-json\/wp\/v2\/media?parent=1426"}],"wp:term":[{"taxonomy":"category","embeddable":true,"href":"https:\/\/techfragments.com\/wp-json\/wp\/v2\/categories?post=1426"},{"taxonomy":"post_tag","embeddable":true,"href":"https:\/\/techfragments.com\/wp-json\/wp\/v2\/tags?post=1426"}],"curies":[{"name":"wp","href":"https:\/\/api.w.org\/{rel}","templated":true}]}}